178032401

Overview Description V 6 42 V IN V 5 24 V OUT 1 I 3 A OUT Quick Start Guide 1 VDRM Variable Step Down Regulator MagIC Power Module Evaluation Board Module TO263-7EP for 171032401 TO263-7EP 5 5 2 Jumpers (J1) for ENABLE & shut off the 4 module 3 Jumpers to set predefined output voltage 2 V OUT Evaluation Board 4 Resistors to set UVLO level 3 5 Terminal block screw connectors for V 178032401 IN and V OUT Default jumper position Absolute maximum ratings Caution: Exceeding the abs. max. values given in the datasheet may affect the device negatively and may cause permanent damage. Version 3.2 Warning Hot surface, please dont touch. Unit is capable to produce tempera- tures above 85 C. Still hot for several minutes after shut down. This evaluation board is intended to be operated in a research and development environment under the supervision of qualified technicians and engineers who are trained and experienced in the safe use of electronics. This evaluation board was designed and tested according to CISPR32 Class B standards under Wrth Elektronik laboratory test conditions, as indicated in the data sheet of the corresponding power module. Operation in other test setups may cause unintended electrical be- havior and exceed the stated performance and limits imposed by the CISPR32 Class B standards. This evaluation board is not intended for usage in final applications. This evaluation board is not intended for resale. WARNING Before operating read the attached IMPORTANT NOTICE document www.we-online.com DIENECKARPRINZEN E-178032401BR.1020.250.FLYSchematic Features Ref.Des. Description (Order Code) Ref.Des. Description (Order Code) 3 U1 MagI C VDRM (171032401) 384 for V = 24 V OUT EN55032 CLASS B ADJ. SS ADJ. FREQ. UVLO OCP OTP T 105C 464 for V = 18 V a Aluminum electrolytic capacitor 220 F/50 V OUT C1 (860160675026) 562 for V = 15 V OUT 715 for V = 12 V (default setting) 2 x Ceramic chip capacitor 4.7 F/50 V OUT CIN Lf (885012209048) 976 for V = 9 V OUT RFBB 1 7 1.91 k for V = 5 V Ceramic chip capacitor 4.7 nF/50 V OUT VIN VOUT VIN VOUT CSS R1 RON1 RON7 (885012007067) To be soldered for adjustable output RFBT CFF Module J2 voltage Ceramic chip capacitor 22 nF/50 V R FBT RENT 2 6 CFF RON FB (885012207094) V OUT + + R = FBB -1 C1 Cf CIN 4 COUT C7 J1 AGND 2 x Ceramic chip capacitor 4.7 F/50 V J3 COUT 0.8 V 3 (885012209048) EN PGND SS 374 k for V = 24 V OUT EP 5 C7 Through hole electrolytic capacitor (optional) RENB CSS RFBB1 ...RFBB7 274 k for V = 18 V OUT 2 x Ceramic chip capacitor 4.7 F/50 V GND GND Cf 232 k for V = 15 V OUT (optional) (885012209048) Optional input lter Optional 182 k for V = 12 V (default setting) OUT Filter inductor, 6.8 H, PD2 (optional) Lf 137 k for V = 9 V OUT (744774068) According to the 12 V industrial rail standard, the UVLO level is set to 9 V using the resistors highlighted with UVLO on the EVB. RON 75 k for V = 5 V OUT The additional aluminium electrolytic capacitor C1 is only for evaluation board protection purposes. It is mounted at the termination R1 0 resistor bridge To be soldered for adjustable frequency of the supply line and provides slight damping of possible oscillations of the series resonance circuit represented by the RENT 124 k inductance of the supply line and the input capacitance. It is not essential for operation. V RENB 18.7 k OUT R = ON -10 RFBT 10 k 1.3 10 sw(ccm)* For accurate V and V voltage measurements it is recommended to measure directly at the input and output capacitors CIN IN OUT Jumper for EN connection to either V and COUT. It is not recommended to use this evaluation board with input and output wire lengths longer than 1 m. IN *Switching frequency in continuous conduction mode J1 (device enabled) or GND (device disabled) For the datasheet of the power module visit us at: