F-221 SUPPLEMENT 6QCD02606.00STLTTR3 (0.635 mm) .025 HIGH-SPEED COAX CABLE ASSEMBLIES SQCD Mates with: SPECIFICATIONS Socket or QTS, QSS Terminal For complete specifications 6QCD Mates with: see www.samtec.com SQCD or QMS, QFS see www.samtec.com 6QCD Cable: 38 AWG coax micro ribbon Signal Routing: 50 Single-EndedW Overall Length: (152 mm) 6 to (1 m) 40 standard 38 AWG Cable Flexing Life: micro ribbon >40,000 cycles Cable Bending Radius: coax cable <2.5 mm Plating: Au over 50 (1.27 m) Ni Propagation Delay: 4.79 nsec/meter Operating Temp Range: -40 C to +105 C RoHS Compliant: Yes Surface Mount RECOGNITIONS NO. POSITIONS For complete scope of TYPE WIRE LENGTH recognitions see PER ROW www.samtec.com/quality (SQCD only) 025, 050, 075 XX.XX (SQCD) = Wire Length in Inches SQCD (43.7 mm) 01.72 Minimum. = Mates with QTS/QSS 026, 052 (6QCD) APPLICATIONS 6QCD = Mates with QMS/QFS (9.28) .365 Processing conditions will OAL = Wire Length + L affect mated height. Wire Length (1.27) .050 ALSO AVAILABLE (MOV Required) Other pin counts Other terminations L END TO END SQCD 6QCD Surface Mount to (24.13) (28.47) .950 1.121 Surface Mount Notes: Cable lengths longer than 40.00 (1 meter) are not supported with S.I. test data. Design your full cable assembly with Samtecs High-Speed Cable Builder at END NO. 1 END NO. 2 www.samtec.com/cablebuilder (-STR SHOWN) (-TTR SHOWN) This Series is non-standard, non-returnable. WWW.SAMTEC.COM Unless otherwise approved in writing by Samtec, all parts and components are designed and built according to Samtecs specifications which are subject to change without notice.6QCD05206.00STLTBR3B SQCD02506.00TTRSTR1 SQCD, 6QCD SERIES HIGH-SPEED COAX CABLE ASSEMBLIES Choice of socket or terminal SCREW MOUNT APPLICATIONS (F, S, B) Choice of Screw Mount end options end options KFE-440-4ET SO0318040102 END END SCREW DOWN WIRING OPTION NO. 1 NO. 2 END OPTION Specify Leave blank for no Screw Option 1 END ASSEMBLIES = Pin 1 to Pin 1 F from chart = End No. 1 2 = Pin 1 to Pin 2 S = End No. 2 3 = Pin 1 to Second Last Pin B = Both Ends 4 = Pin 1 to Last Pin END SURFACE MOUNT Terminal, Top, TTR Notch Right Terminal, Top, TTL NO. OF Notch Left SERIES A B POSITIONS Terminal, Bottom, 025 (40.10) 1.579 (34.00) 1.339 TBR Notch Right (60.10) 2.366 (54.00) 2.126 SQCD 050 Terminal, Bottom, TBL 075 (80.10) 3.154 (74.00) 2.913 Notch Left 026 (45.47) 1.790 (39.50) 1.555 Socket, Top, 6QCD STR (66.80) 2.630 (61.00) 2.402 Notch Right 052 A B Socket, Top, STL Notch Left Socket, Bottom, SBR Notch Right Socket, Bottom, SBL Notch Left (3.28) .129 DIA SURFACE MOUNT (XTX & XBX) SCREW DOWN OPTIONS WWW.SAMTEC.COM Unless otherwise approved in writing by Samtec, all parts and components are designed and built according to Samtecs specifications which are subject to change without notice.