D2X Detection Switch A Switch with Crimp-type Connectors that Greatly Reduces Wiring Work Clip-on wiring via crimp-type connectors. Snap-fit attachment for easy installation. 2 X Operation possible from either side to enable mounting in either direction. RoHS Compliant List of Models Characteristics Mode Permissible operating speed 0.1 mm to 100 mm/s D2X-C Permissible Mechanical 60 operations/min operating Electrical 30 operations/min frequency Contact Form Insulation resistance 100 M min. (at 250 VDC with insulation tester) Contact resistance (initial value) 200 m max. SPST-NC Between terminals of the 250 VAC 50/60 Hz for 1 min same polarity Dielectric strength Between current-carrying 250 VAC 50/60 Hz for 1 min metal parts and ground Vibration Malfunction 10 to 55 Hz, 1.5 mm double amplitude resistance 2 Destruction 500 m/s approx. 50G max. Shock resistance 2 Malfunction 300 m/s approx. 30G max. Mechanical 1,000,000 operations min. (60 operations/min) Durability * Electrical 50,000 operations min. (30 operations/min) NC COM Degree of protection IEC IP00 -10C to +70C (at ambient humidity Contact Specifications Ambient operating temperature of 60% max.) (with no icing or condensation) Specification Slide Ambient operating humidity 45% to 85% (for +5C to +35C) Contact Material Gold plated Weight Approx. 1 g Minimum applicable load (reference value) * 5 VDC 1 mA Note. The data given above are initial values. * For testing conditions, consult your OMRON sales representative. * Please refer toUsing Micro Load inPrecaution for more information on the minimum applicable load. Ratings Rated voltage Resistive load 30 VDC 0.1 A Note. The above rating values apply under the following test conditions. (1) Ambient temperature: 202C (2) Ambient humidity: 655% (3) Operating frequency: 30 operations/min 1D2X Detection Switch Mounting Holes (Unit: mm) Refer to the following diagram for mounting hole dimensions, and make sure that the burr is placed to backside of Mounting Plate. When thickness of the plate (t) is 1.6 mm. When thickness of the plate (t) is 1.2 mm. 2-R0.6 2-R0.6 4.8 12.9 8-R1 1.8 2-R0.5 +0.1 0.05 0.0500.05.05 2- 3.2 4.4 3.233.2.2 dia. dia.dia. 3.2 dia. +0.1 3.5 dia. 0 2-R0.5 0.1 2- 8 4.4 5.2 10.8 +0.1 R0.5 0 10.8 0 R0.5 2-R1.6 4-R1 5 3.4 +0.1 4 5 3.2 0 0.1 12.2 2.7 5 2-R0.6 2-R0.6 2 X Note 1. Allowable deviation from the center is 0.07 mm. Note 2. Unless otherwise specified, a tolerance of 0.1 mm applies to all dimensions. Dimensions (Unit: mm) and Operating Characteristics D2X-C Direction A Direction B Boss of the reverse side TTP=MIN6.34 2-The center of 3.1 mm dia. Operating Force OF Max. 0.49 N 50 gf (Rotational angle equals 25) Releasing Force RF Min. 0.02 N 2 gf Stroke metrics Stroke metrics (Direction B) 20 20 (Direction A) Operating Position OP 0.52 to 2.35 mm OP=2.35 max. Total Travel Position TTP Min. 6.34 mm 4.8 (Rotational angle equals 9) OP=0.52 min. (0.2) (Rotational angle equals 2) Stroke metrics Direction A Direction B 1.55 2-3.1 dia. 15 0.52 min. 0.52 min. Completely ON Completely OFF 11.9 3.8 2.35 max. 2.35 max. 12.2 8 (17) 6 Total Travel Total Travel Position 6.34 min. Position 6.34 min. Actuator stroke (mm) 5.1 * 1 5.8 1.6 0.4 3.3 6.2 * Dimensions of the marked parts are designed by Tyco 5.3 Electronics Japan. This part is identical to Tyco Electronics Japan s CT connectors (dipole type) in size. Note 1. Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. Note 2. The operating characteristics are for cases where the actuator operates in the A ( ) direction or B ( ) direction. Precautions Please refer toBasic Switches Common Precaution for correct use. Correct Use Terminal Connection Do not use the Switch with Connector mounted and weight load applied to the Connector and lead wire, otherwise it may rattle or may result in connection failure. Wiring Connector Use the CT Connector made by Tyco Electronics Japan for Tyco Electronics Corporation, TE Connectivity Ltd. wiring. For products and technical support, contact the Crimp-style connector housing: 179228-2, Crimp-style Web: