TPP3XGDS0x000E2G 850nm SFP+ Transceiver Features 850nm VCSEL laser Transmission distance up to 300m on OM3 MM fiber Low power consumption Wide Case Operating Temperature Range Compliant with SFP+ Electrical MSA SFF-8431 Compliant with SFP+ Mechanical MSA SFF-8432 Digital Diagnostics Monitoring (DDM) through Serial Interface comply with SFF-8472, Rev. 10.4 RoHS 6/6 compliant Compliant with product safety standards Description The TPP3XGDS0x000E2G is an enhanced small form The TPP3XGDS0x000E2G transceiver connects to factor pluggable (SFP+) fiber optic transceiver with digital standard 20-pad SFP+ connectors for hot plug capability. diagnostics monitoring functionality (DDM). Supporting This allows the system designer to make configuration Ethernet and Fiber Channel standards makes it ideally changes or maintenance by simply plugging in different suited for 10Gbps data-com and storage area network transceivers without removing the power supply from the applications. DDM functionality (alarm and warning host system. The transmitter and receiver DATA interfaces 2 features) is integrated into the design via an I C serial are internally AC-coupled. LV-TTL Transmitter Disable interface per the Multi-Source Agreement (MSA) SFF-8472, control input and Loss of Signal (LOS) output interfaces Rev. 10.4. are also provided. The transceiver supports data rates ranging from The transceiver has bail-type latch, which offers an easy 11.3Gbps down to 8Gbps. It provides an excellent solution and convenient way to release the modules. The latch is compliant with the SFP MSA. for transmission at 850nm over up to 300m 2000MHzkm multimode fiber. The sub-watt power consumption and The transceiver operates from a single +3.3V power supply excellent EMI performance allow system design with high over an operating case temperature range of -5C to port density. The product is RoHS compliant and is +70C (Commercial), or -5C to +85C (Extended). The designed and tested in accordance with industry safety housing is made of metal for EMI immunity. standards. The transceiver is Class I Laser product per U.S. FDA/CDRH and international IEC-60825 standards. Absolute Maximum Ratings Parameters Symbol Min Max Units Storage Temperature Range T - 40 + 85 C ST Operating Commercial - 5 + 70 Temperature T C OP 1 Extended - 5 + 85 Range 2 Operating Relative Humidity RH 0 85 % Supply Voltage Range V - 0.5 + 3.6 V CC 1 Measured on top side of SFP+ module at the front center vent hole of the cage 2 Non condensing 46335 Landing Pkwy Fremont CA 94538-6407Tel: 510-933-7200Fax: 510-933-7300Email: info oplink.com Web: www.oplink.com Page 1 of 6 S0365. Rev.01. 2012-11-27 TPP3XGDS0x000E2G 850nm SFP+ Transceiver Transmitter Performance Characteristics (Over Operating Case Temperature, V =3.13 to 3.47V) CC Parameter Symbol Min Typ Max Units B 8.0 - 11.3 Gb/s Data Rate Center Wavelength 840 850 860 nm C Spectral Width - - 0.45 nm rms 1 Average Launch Power P - 5 - - 1 dBm avg 1 Launch Power in OMA P - - 1.5 - dBm OMA Extinction Ratio ER 3 - - dB Relative Intensity Noise RIN OMA - - - 128 dB/Hz 12 Average Launch Power of OFF Transmitter P - - - 30 dBm off Transmitter and Dispersion Penalty 10.3125Gb/s TDP - - 3.9 dB 1 Launch power figures are informative only, per IEEE 802.3ae. Receiver Performance Characteristics (Over Operating Case Temperature, V =3.13 to 3.47V) CC Parameter Symbol Min Typ Max Units B 8.0 - 11.3 Gb/s Data Rate Wavelength of Operation 840 - 860 nm 1 P 10.3125Gb/s - - - 9.9 avg Receiver Sensitivity P dBm min 1 OMA 10.3125Gb/s - - - 11.1 2 - Stressed Receiver Sensitivity in OMA ( 10.3125Gb/s) - - - 7.5 dBm -12 P Maximum Input Power (10 BER) MAX + 0.5 - - dBm LOS Hysteresis - 0.5 - - dB Increasing Light Input P - - - 11 los+ LOS Thresholds dBm Decreasing Light Input P - 30 - - los- 1 -12 31 Specified with BER <1x10 and PRBS 2 -1. 2 Compliant with IEEE 802.3ae Note: The specified characteristics are met within the recommended range of operation. Unless otherwise noted typical data are quoted at nominal voltage and +25C ambient temperature. Laser Safety: All transceivers are Class I Laser products per Oplink Communications, Inc. FDA/CDRH and IEC-60825 standards. They must be DATE OF MANUFACTURE: operated under specified operating conditions. This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements 46335 Landing Pkwy Fremont CA 94538-6407Tel: 510-933-7200Fax: 510-933-7300Email: info oplink.com Web: www.oplink.com Page 2 of 6 S0365. Rev.01. 2012-11-27