25W Multiple-Stage Constant Current Mode LED Driver LCM -25DA se ries Users Manual 2 (for DA2-Type only) (for DA-Type only) IS 15885(Part 2/Sec13) THOMAS SAMUEL THOMAS SAMUEL R-41027766 (except for DA2-Type)(except for DA2-Type) File Name:LCM-25DA-SPEC 2021-09-0325W Multiple-Stage Constant Current Mode LED Driver LCM -25DA se ries SPECIFICATION MODEL LCM-25 Current level selectable via DIP switch, please refer toDIP SWITCH TABLE section CURRENT LEVEL 350mA 500mA 600mA 700mA(default) 900mA 1050mA RATED POWER 18.9W 25.2W DC VOLTAGE RANGE 6 ~ 54V 6 ~ 50V 6 ~ 42V 6 ~ 36V 6 ~ 28V 6 ~ 24V OUTPUT OPEN CIRCUIT VOLTAGE (max.) 59V 41V CURRENT RIPPLE 5.0% max. rated current CURRENT TOLERANCE 5% Note.3 SETUP TIME 500ms / 230VAC Note.8 180 ~ 277VAC 254 ~ 380VDC(254~375VDC for DA2-Type) VOLTAGE RANGE Note.2 (Please refer toSTATIC CHARACTERISTI section) FREQUENCY RANGE 47 ~ 63Hz PF0.94/230VAC, PF0.91/277VAC full load POWER FACTOR (Typ.) (Please refer toPOWER FACTOR (PF) CHARACTERISTI section) THD< 20%( load50%/230VAC load75%/277VAC) TOTAL HARMONIC DISTORTION (Please refer to TOTAL HARMONIC DISTORTION(THD) section) EFFICIENCY (Typ.) Note.4 86% INPUT AC CURRENT (Typ.) 0.17A/230VAC 0.15A/277VAC INRUSH CURRENT (Typ.) COLD START 20A(twidth=260s measured at 50% Ipeak) at 230VAC Per NEMA 410 MAX. No. of PSUs on 16A 26 units (circuit breaker of type B) / 44 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.5mA / 240VAC STANDBY POWER <0.5W CONSUMPTION Note.5 SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down DIMMING Please refer toDIMMING OPERATIO section FUNCTION Please refer toSYNCHRONIZATION OPERATION section SYNCHRONIZATION WORKING TEMP. Tcase=-30 ~ +85 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=+85 WORKING HUMIDITY 20 ~ 90% RH non-condensing ENVIRONMENT -40 ~ +80, 10 ~ 95% RH STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT 0.03%/ (0 ~ 50) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes UL8750(except for DA2-Type), CSA C22.2 NO.250.0-08, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384 SAFETY STANDARDS independent,GB19510.14,GB19510.1,BIS IS15885(except for DA2-Type), EAC TP TC 004 approved According to BS EN/EN61347 -2 -13 appendix J suitable for emergency installations DALI STANDARDS IEC62386-101, 102, 207,251 SAFETY & WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-DA:1.5KVAC O/P-DA:1.5KVAC EMC ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C( load50%) BS EN/EN61000-3-3 GB17625.1,GB17743, EMC EMISSION Note.6 EAC TP TC 020 Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, light industry level(surge immunity Line-Line 2KV), EMC IMMUNITY EAC TP TC 020 MTBF 213.3K hrs min. MIL-HDBK-217F (25) DIMENSION 105*68*23mm (L*W*H) OTHERS PACKING 0.17Kg 72pcs/13.2Kg/1.04CUFT NOTE ,