TLE9461ES V33 Lite CAN SBC Family 1 Overview Features Key Features Very low quiescent current consumption in Stop- and Sleep Mode Periodic Cyclic Wake in SBC Normal-, Stop- and Sleep Mode Periodic Cyclic Sense in SBC Normal-, Stop- and Sleep Mode Low-Drop Linear Voltage Regulator 3.3 V, 150 mA (250 mA peak) for main supply, Low-Drop Linear Voltage Regulator 5 V, 100 mA, protection feature for off-board usage High-Speed CAN transceiver supporting FD communication up to 5 Mbit/s according to ISO 11898-2:2016 & SAE J2284 Fully compliant to Hardware Requirements for LIN, CAN and FlexRay Interfaces in Automotive Applications Revision 1.3, 2012-05-04 Charge pump-output for N-channel MOSFET reverse-polarity protection or load switch feature with integrated spread spectrum modulation feature for optimum EMC performance Universal High-Voltage Wake input for voltage level monitoring and wake-up detection General Purpose High-Voltage in- and output (GPIO) configurable as Fail Output, Wake Input, Low-Side switch or High-Side switch High-Voltage Measurement function as alternative pin assignment Fail Output for Fail-Safe signalization Configurable wake-up sources Reset & Interrupt outputs Configurable timeout and window watchdog Overtemperature and short circuit protection feature Dedicated TEST pin for SBC Development Mode entry (watchdog counter stopped) Software compatible to other SBC families TLE926x and TLE927x Wide input voltage and temperature range Optimized for Electromagnetic Compatibility (EMC) and low Electromagnetic Emission (EME) Optimized for high immunity against Electromagnetic Interference (EMI) AEC Qualified & Green Product (RoHS compliant) Datasheet Rev. 1.1 www.infineon.com 1 2019-09-27 TLE9461ES V33 Lite CAN SBC Family Overview Scalable System Basis Chip (SBC) Family Product family for complete scalable application coverage Optimized feature set for optimal system design Dedicated Data Sheets are available for all product variants Complete compatibility (hardware- and software across the family) Same PG-TSDSO-24-1 package with exposed pad (EP) for all product variants CAN Partial Networking variants (-3ES) Product variants for 5 V (TLE94xxyy) and 3.3 V (TLE94xxyyV33) output voltage for main regulator Software compatible to other SBC families TLE926x and TLE927x Potential applications HVAC ECU and Control panel Light Control Unit (LCU) for front, rear and ambient Seat control module Seat belt pretension Steering column and steering lock Closure (trunk, sliding door, etc.) Gear shifters and selectors Smart power distribution modules Product validation Qualified for automotive applications. Product validation according to AEC-Q100/101. Description The TLE9461ES V33 is a monolithically integrated circuit in an exposed pad PG-TSDSO-24-1 (150 mil) power package. The device is designed for various CAN automotive applications as main supply for the microcontroller and as interface for a CAN bus network. To support these applications, the System Basis Chip (SBC) provides the main functions, such as a 3.3 V low- dropout voltage regulator (LDO) for e.g. a microcontroller supply, another 5 V low-dropout voltage regulator with off-board protection for e.g. sensor supply, a HS-CAN transceiver supporting CAN FD for data transmission, a high-voltage GPIO with embedded protective functions and a 16-bit Serial Peripheral Interface (SPI) to control and monitor the device. Also a configurable timeout / window watchdog circuit with a reset feature, one dedicated fail output and an undervoltage reset feature are implemented. The device offers low-power modes in order to minimize current consumption in applications that are connected permanently to the battery. A wake-up from the low-power mode is possible via a message on the CAN bus, via the bi-level sensitive monitoring/wake-up input as well as via Cyclic Wake. The device is designed to withstand the severe conditions of automotive applications Type Package Marking TLE9461ES V33 PG-TSDSO-24-1 TLE9461ESV33 Datasheet 2 Rev. 1.1 2019-09-27