Product Specification 8.5 Gb/s Short-Wavelength SFP+ Transceiver FTLF8528P3BxV PRODUCT FEATURES Up to 8.5 Gb/s bi-directional data links Hot-pluggable SFP+ footprint Built-in digital diagnostic functions 850nm Oxide VCSEL laser transmitter Duplex LC connector RoHS compliant and Lead Free 50m on 50/125m MMF 150m on high-bandwidth APPLICATIONS 50/125um (OM3) MMF Metal enclosure, for lower EMI Tri-Rate 2.125/4.25/8.5 Gb/s Fibre Single 3.3V power supply Channel < 0.5W power dissipation Wireless CPRI Extended operating temperature Wireless - OBSAI range: -5C to 85C Finisars FTLF8528P3BxV SFP+ transceivers are designed for use in Fibre Channel links up to 8.5 Gb/s data rate over multimode fiber. They are compliant with FC-PI-4 Rev. a c b 8.00 and SFF-8472 Rev 11.0 , and compatible with SFF-8432 and applicable portions d of SFF-8431 Rev. 4.1 . The product is RoHS compliant and lead-free per Directive e 2002/95/EC and Finisar Application Note AN-2038. PRODUCT SELECTION FTLF8528P3BxV o x N Extended Temperature, -5C to 85 C o C Commercial Temperature, -5 to 70 C Finisar Corporation Jan 25, 2011 Rev. A.3 Page 1 FTLF8528P3BxV Pluggable SFP+ Product Specification January 2011 4. Pin Descriptions Pin Symbol Name/Description Ref. 1 V Transmitter Ground (Common with Receiver Ground) 1 EET 2 T Transmitter Fault. 2 FAULT 3 T Transmitter Disable. Laser output disabled on high or open. 3 DIS 4 SDA 2-wire Serial Interface Data Line (MOD-DEF2) 4 5 SCA 2-wire Serial Interface Clock (MOD-DEF1) 4 6 MOD ABS Module Absent, connected to V or V 4 EET EER 7 RS0 Rx Rate Select: 5 Open or Low = 2.125 or 4.25 Gb/s Fibre Channel (Low Bandwidth) High = 8.5 Gb/s Fibre Channel (High Bandwidth) 8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 6 9 RS1 Tx Rate Select: 5 Open or Low = 2.125 or 4.25 Gb/s Fibre Channel (Low Bandwidth) High = 8.5 Gb/s Fibre Channel (High Bandwidth) 10 V Receiver Ground (Common with Transmitter Ground) 1 EER 11 V Receiver Ground (Common with Transmitter Ground) 1 EER 12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 V Receiver Ground (Common with Transmitter Ground) 1 EER 15 V Receiver Power Supply CCR 16 V Transmitter Power Supply CCT 17 V Transmitter Ground (Common with Receiver Ground) 1 EET 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 V Transmitter Ground (Common with Receiver Ground) 1 EET Notes: 1. Circuit ground is internally isolated from chassis ground. 2. T is an open collector/drain output, which should be pulled up with a 4.7k 10k Ohms resistor on the host board if FAULT intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 3. Laser output disabled on T >2.0V or open, enabled on T <0.8V. DIS DIS 4. Should be pulled up with 4.7k 10kohms on host board to a voltage between 2.0V and 3.6V. MOD ABS pulls line low to indicate module is plugged in. c 5. Rate select can also be set through the 2-wire bus in accordance with SFF-8472 v. 11.0 . Rx Rate Select is set at Bit 3, Byte 110, Address A2h. Tx Rate Select is set at Bit 3, Byte 118, Address A2h. Note: writing a 1 selects maximum bandwidth operation. Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. 6. LOS is open collector output. Should be pulled up with 4.7k 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation logic 1 indicates loss of signal. Finisar Corporation Jan 25, 2011 Rev. A.3 Page 2