Product Specification 1000BASE-T RoHS Compliant Copper SFP Transceiver FCLF8520P2BTL / FCLF8521P2BTL / FCLF8522P2BTL Product Features Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint Extended case temperature range (-40C to +85C ) Fully metallic enclosure for low EMI RoHS compliant and Lead Free Low power dissipation (1.05 W typical) Compact RJ-45 connector assembly Access to physical layer IC via 2-wire Applications serial bus 1.25 Gigabit Ethernet over Cat 10/100/1000 BASE-T operation in host 5 cable systems with SGMII interface Finisars FCLF8520P2BTL, FCLF8521P2BTL and FCLF8522P2BTL 1000BASE-T Copper Small 1 Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the Gigabit Ethernet and 1000BASE-T standards as specified in IEEE Std 2 3 802.3 . The transceiver is RoHS compliant and per Directive 2011/65/EU and Finisar Application Note AN-2038. The 1000BASE-T physical layer IC (PHY) can be accessed via I2C, allowing access to all PHY settings and features. The FCLF8520P2BTL uses the SFPs RX LOS pin for link indication, and 1000BASE-X auto- negotiation should be disabled on the host system. The FCLF8521P2BTL is compatible with 1000BASE-X auto-negotiation, but does not have a link indication feature (RX LOS is internally grounded). See AN-2036, Frequently Asked Questions Regarding Finisars 1000BASE-T SFPs, for a more complete explanation on the differences between the two models and details on applications issues for the products. The FCLF8522 shall support both RX LOS pin for link indication and 1000BASE-X auto-negotiation. PRODUCT SELECTION Part Number Link Indicator on RX LOS Pin 1000BASE-X auto-negotiation enabled by default FCLF8520P2BTL Yes No FCLF8521P2BTL No Yes Finisar Corporation July 2015 Rev E Page 1 FCLF8520P2BTL, FCLF8521P2BTL and FCLF8522P2BTL Product Specification FCLF8522P2BTL Yes Yes I. SFP to Host Connector Pin Out Pin Symbol Name/Description Note 1 V Transmitter ground (common with receiver ground) 1 EET 2 T Transmitter Fault. Not supported FAULT 3 T Transmitter Disable. PHY disabled on high or open 2 DIS 4 MOD DEF(2) Module Definition 2. Data line for serial ID 3 5 MOD DEF(1) Module Definition 1. Clock line for serial ID 3 6 MOD DEF(0) Module Definition 0. Grounded within the module 3 7 Rate Select No connection required 8 LOS Loss of Signal indication. 4 9 V Receiver ground (common with transmitter ground) 1 EER 10 V Receiver ground (common with transmitter ground) 1 EER 11 V Receiver ground (common with transmitter ground) 1 EER 12 RD- Receiver Inverted DATA out. AC coupled 13 RD+ Receiver Non-inverted DATA out. AC coupled 14 V Receiver ground (common with transmitter ground) 1 EER 15 V Receiver power supply CCR 16 V Transmitter power supply CCT 17 V Transmitter ground (common with receiver ground) 1 EET 18 TD+ Transmitter Non-Inverted DATA in. AC coupled 19 TD- Transmitter Inverted DATA in. AC coupled 20 V Transmitter ground (common with receiver ground) 1 EET Notes: 1. Circuit ground is isolated from chassis ground 2. PHY disabled on T > 2.0V or open, enabled on T < 0.8V DIS DIS 3. Should be pulled up with 4.7k 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD DEF(0) pulls line low to indicate module is plugged in. 4. LVTTL compatible with a maximum voltage of 2.5V. Not supported on FCLF8521P2BTL. Table 1. SFP to host connector pin assignments and descriptions VeeT 20 1 VeeT TD- 19 2 TXFault TD+ 18 3 TX Disable VeeT 17 4 MOD-DEF(2) VccT 16 5 MOD-DEF(1) Towards Towards VccR 15 Bezel 6 MOD-DEF(0) ASIC VeeR 14 7 Rate Select RD+ 13 8 LOS RD- 12 9 VeeR VeeR 11 10 VeeR Figure 1. Diagram of host board connector block pin numbers and names Finisar Corporation July 2015 Rev E Page 2