Ships to you between Wed. 17 Jul to Fri. 19 Jul
EA DIPS082-HNLED Display Visions
Ships to you between Thu. 11 Jul to Wed. 17 Jul
Issue 10.2016 LCD-Modul 2x8 - 5.01mm INCL. CONTROLLER ST7066 Dimension 40 x 20 mm FEATURES * SUPER SMALL LCD MODULE * HIGH CONTRAST LCD-SUPERTWIST DISPLAY (BLUE/NEUTRAL) * OPTIONAL LED-BACKLIGHT YELLOW/GREEN * HD 44780 COMPATIBLE * 4- OR 8-BIT DATA BUS INTERFACE * ASCII CHARACTER SET BUILT IN * ALSO AVAILABLE: 1x8 LCD WITH SAME DIMENSIONS * POWER SUPPLY +5V OR 2.7V OR 3.3V 2mA and 50mA for LED-B/L (5V) * OPERATING TEMPERATURE RANGE EA DIPS082: -20+70C * OPERATING TEMPERATURE RANGE EA 8081-A3N: 0+50C * NO MORE MOUNTING REQUIRED: SIMPLY PLUG INTO PCB ORDERING INFORMATION LCD-MODULE 2x8 - 5.01mm EA DIPS082-HN WITH LED BACKLIGHT YELLOW/GREEN EA DIPS082-HNLED LCD-MODULE 1x8 - 7.15 mm EA 8081-A3N no more mounting required2x8 - 5.01mm Pinout Contrast setting Pin Symbol Level Function Pin Symbol Level Function 1 VSS L Power Supply 0V (GND) 8 D1 H/ L Display Data 2 VDD H Power Supply +5V 9 D2 H/ L Display Data 3 VEE - Contrast (about 0.3V / 1.2V) 10 D3 H/ L Display Data 4 RS H/ L H=Data / L=Command 11 D4 (D0) H/ L Display Data 5 R/W H/ L H=Read / L=Write 12 D5 (D1) H/ L Display Data 6 E H Enable (falling edge) 13 D6 (D2) H/ L Display Data 7 D0 H/ L Display Data / Anode LED-B/L 14 D7 (D3) H/ L Display Data, MSB LED Backlight Standard display EA DIPS082-HN is reflective, non-backlighted version. Module with part number EA DIPS082-HNLED comes with yellow/green LED backlight. Power consumption for backlight is 50mA typ. and 80mA max. Backlight is permanent switched on. Supply voltage with backlight is 5V only. For individual use LED backlight can be switched on and off after doing the following modification: Remove series resistor R5 and change resistor from R6 to R7. Now a positive voltage at pin 7 (D0) powers Anode of backlight direct. To limit LED-current an external series resistor is required (R = Ext. 0,8V / I ). Please note that in this case display interface is 4-bit mode only LED Table of commands Code Execute Instruction Description Time DB DB DB DB DB DB DB DB R/W RS 7 6 5 4 3 2 1 0 (max.) Clears all display and returns the cursor Clear Display 0 0 0 0 0 0 0 0 0 1 1.64ms to the home position (Address 0). Returns the Cursor to the home position (Address 0). Also returns the Cursor At Home 0 0 0 0 0 0 0 0 1 * display being shifted to the original 1.64ms position. DD RAM contents remain unchanged. Sets the Cursor move direction and specifies or not to shift the display. Entry Mode Set 0 0 0 0 0 0 0 1 I/D S 40s These operation are performed during data write and read. Sets ON/OFF of all display (D) cursor Display On/Off 0 0 0 0 0 0 1 D C B ON/OFF (C), and blink of cursor position 40s Control character (B). Moves the Cursor and shifts the display Cursor / Display Shift 0 0 0 0 0 1 S/C R/L * * 40s without changing DD RAM contents. Sets interface data length (DL) number of display lines (N) and character font Function Set 0 0 0 0 1 DL N F * * 40s (F). Sets the CG RAM address. CG RAM CG RAM Address Set 0 0 0 1 ACG data is sent and received after this 40s setting. Sets the DD RAM address. DD RAM data is sent and received after this DD RAM Address Set 0 0 1 ADD 40s setting. Reads Busy flag (BF) indicating internal Busy Flag / Address operation is being performed and reads 0 1 BF AC - Read address counter contents. CG RAM / DD RAM 1 0 Write Data Writes data into DD RAM or CG RAM 40s Data write CG RAM / DD RAM Reads data from DD RAM or CG RAM 1 1 Read Data 40s Data Read Page 2 Printing and typographical errors reserved. ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
