DS760SL-3

Embedded Power for Business-Critical Continuity Rev. 03.15.11 80 DS760SL Series 1 of 8 DS760SL Series 760 Watts Bulk Front End Total Output 760 Watts Power: +5.0 Vdc Stand-by Electrical Specifications Special Features Input Input ra nge (operating): 90 - 264 Vac 760 W output power Input range (nominal): 115 / 230 Vac Input through IEC connector 18.1 W/cu-in Frequency: 47 - 63 Hz 1U X 54.5 mm form factor (slimline) N + 1 redundant Input fusing: Internal 10 A fuses Both lines fused Hot-swap Inrush current: <= 25 A peak Either hot or cold start Internal ORing Power factor: 0.99 typical Meets EN61000-3-2 5.0 V housekeeping Harmonics: Meets IEC 1000-3-2 requirements High efficiency 91% 230 Vac, Input current: 8.8 A RMS max input current At 100 Vac 50% load Variable speed smart fans Holdup time: 12 ms minimum for main O/P At full rated load EMI Class A 20 ms minimum for standby EN610 00 Immunity Undervoltage lockout: 85 2.5 Vac Turn-on voltage Two year war rant y 80 2.5 Vac Turn-off voltage Overvoltage lockout: N/A Leakage current: < 0.8 mA At 264 Vac On/Off power switch: N/A Power line transient: MOV directly after the fuse Environmental Specifications Operating temperature: -10 to 50 C Storage temperature: -40 to 85 C Cooling: Internal fan (fan speed control) Operating relative humidity: 5% to 95% non-condensing Altitude: 10,000 feet Safety RoHS compliant: Yes UL/cUL 60950 -1 CSA 60950-1 VDE 60950-1 China CCC CB Scheme Report/CertEmbedded Power for Business-Critical Continuity Rev. 03.15.11 80 DS760SL Series Efficiency Curve 760 W DS Slim (STD Air) 2 of 8 92.0% 90.0% 88.0% 230 Vac, 50Hz 86.0% 115 Vac, 60Hz 84.0% 82.0% 80.0% 0.0 100.0 200.0 300.0 400.0 500.0600.0 700.0800.0 900.0 Output Power W Output Output rating: 12 V 62.3 A 748 W 90 - 264 Vac 5.0 Vsb 2.4 A 12 W 2 Setpoint: 12.0 V Programmable 5% through I C serial bus Total regulation range: 12 V 1% Line/load/transient when measured at output 5.0 Vsb 3% connector Rated load: 760 W maximum No derating over operating temp range Minimum load: 12 V 0.0 A No loss of regulation 5.0 Vsb 0.0 A Output noise (PARD): 100 mV Max P-P 12.0 V output 100 mV Max P-P 5.0 Vsb output Measured with a 0.1 uF ceramic and 10 uF tantalum capacitor on any output 20 Mhz Output voltage overshoot: 300 mV 12 V main 1 A/uSec slew rate 200 mV 5.0 standby Transient response: < 250 uSec 50% load step 1 A/us Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Max units in parallel: Up to 4 Short circuit protection: To 120% of rated output Output to return Remote sense: Compensation up to 100 MV Output isolation: Standard per Safety Requirements Forced load sharing: To within 10% of all shared outputs Digital sharing control Overload protection (OCP): 120% to 130% 12 V output 120% to 170% 5.0 Vsb output Overvoltage protection (OVP): 110% to 120% 12 V output 110% to 125% 5.0 Vsb output Overtemperature protection: 10 - 15 C above safe operating area Both PFC and output converter monitored Ordering Information O/P Voltage Set Point Total Minimum Maximum Output Stand-by Model Number Air Flow Set Point Tolerance Regulation Current Current Ripple P/P Voltage DS760SL-3 12.0 Vdc 0.2% 1% 0 A 62.3 A 120 mV 5.0 V 2.4 A Standard DS760SL-3-001 12.0 Vdc 0.2% 1% 0 A 50.0 A 120 mV 5.0 V 2.4 A Reverse DS760SL-3-002 12.0 Vdc 0.2% 1% 0 A 62.3 A 120 mV 3.3 V 2.4 A Standard DS760SL-3-003 12.0 Vdc 0.2% 1% 0 A 50.0 A 120 mV 3.3 V 2.4 A Reverse Efficiency