High power low ohmic chip resistors Wide terminal type LTR series Datasheet Features 1)Chip Resistors for current detection : 10m ~ 2)High joint reliability with long side terminations. 3)Improvement of rated power enables to displace smaller size of resistors,and it contributes space savings in your set. 4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 5)Corresponds to AEC-Q200. Products list Rated Operating Size Resistance Temperature power Resistance range temperature Part No. tolerance coefficient (70) range (mm) (inch) (W) (%) (ppm / ) () () 150 0.047R<0.100 (E24 series) F ( 1% ) LTR10 2012 0805 0.5 -55 +155 J ( 5% ) (E24 series) 150 0.100R<10 (E24 series) 0300 R0.010 (E24 series) 0300 0.010R0.020 F ( 1% ) (E24 series) LTR18 3216 1206 1.0 0200 0.020R0.050 -55 +155 J ( 5% ) (E24 series) 0150 0.050R0.500 (E24 series) 100 0.500R1.000 0300 R0.010 (E24 series) 0300 0.010R0.020 (E24 series) F ( 1% ) (E24 series) LTR50 2550 1020 2.0 0200 0.020R0.051 -55 +155 J ( 5% ) (E24 series) 0150 0.051R0.100 (E24 series) 100 0.100R0.910 F ( 1% ) (E24 series) 0+150 0.100R<0.200 F ( 1% ) (E24 series) LTR100 6432 2512 2.0 0+100 0.200R<1 -55 +155 J ( 5% ) (E24 series) 200 0.100R<1 Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Part number description L T R 1 0 E V H J L 1 R 0 Resistance Special Part No. Size (mm inch ) Packaging specifications code Nominal resistance tolerance part code Resistance code, 3 or 4 digits. 10(2012 0805 ) Packaging Quantity Part No. Code F (1%) U 10m LTR specifications / Reel 18(3216 1206 ) Resistance J (5%) S 11m (High power 50(2550 1020 ) tolerance Resistance Paper tape 91m chip resistors LTR10 EVH 5000 + code 100(6432 2512 ) (4mm Pitch) L 100m Wide terminal Special code Paper tape type) LTR18 EZP 5,000 (4mm Pitch) FU, FS 4 digits FL, JS Embossed tape LTR50 UZP 5,000 3 digits JU, JL (4mm Pitch) Embossed tape LTR100 JZP 4,000 (4mm Pitch) www.rohm.com 1/4 2018 ROHM Co., Ltd. All rights reserved. 2018.09 - Rev.ILTR series -low ohmic- Datasheet Chip resistor dimensions and markings LTR10 LTR 18 / 100 LTR 50 <Marking method> There are four digits used for the calculation number according to IEC code.L means decimal point of m unit in case resistance value is 0.01 or less.R means decimal point of unit in case resistance value is above 0.01. Example : 4digits10m=10L0, 100m=R100 3digits100m=R10, 1=1R0 (Unit:mm) Marking Part No. (mm) (inch) L W t a b existence LTR10 2012 0805 1.20.10 2.00.10 0.550.10 0.300.20 0.350.20 Yes LTR18 3216 1206 1.60.10 3.20.10 0.580.10 0.500.20 0.500.20 No LTR50 2550 1020 2.500.15 5.000.15 0.580.15 0.380.20 0.900.20 Yes No LTR100 6432 2512 3.20.15 6.40.15 0.550.15 0.400.25 1.130.25 Land pattern example (Unit:mm) Dimensions A B C D Part No. LTR10 0.50 1.98 2.20 0.74 LTR18 0.55 2.90 3.20 1.18 LTR50 0.80 3.35 5.00 1.28 LTR100 0.83 3.69 6.40 1.43 www.rohm.com 2/4 2018 ROHM Co., Ltd. All rights reserved. 2018.09 - Rev.I