I A T F SMT Power Inductor High Current Molded Power Inductor - PA4547 & PM4547 Series POWER PRODUCTS Height: 1.5mm Max Footprint: 3.8mm x 3.4mm Max Current Rating: up to 7.0A Inductance Range: 0.22uH to 10.0uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise 200Vdc Isolation between terminal and core Electrical Specifications 25C - Operating Temperature -55C to +125C DC Resistance 5 3 2 Inductance Rated Saturation 5,6 5,6 100KHz, 1.0V Current Current Commercial Automotive TYP. MAX. uH20% A m m A PA4547.221NLT PM4547.221NLT 0.22 7.00 14 17 10.8 PA4547.471NLT PM4547.471NLT 0.47 5.50 23.3 28 8.0 PA4547.561NLT PM4547.561NLT 0.56 5.00 28 33 7.2 PA4547.681NLT PM4547.681NLT 0.68 4.50 34 42 6.5 PA4547.102NLT PM4547.102NLT 1.00 3.60 41 50 5.8 PA4547.152NLT PM4547.152NLT 1.50 3.40 64 77 4.0 PA4547.222NLT PM4547.222NLT 2.20 3.20 82 98 3.8 PA4547.332NLT PM4547.332NLT 3.30 2.50 170 205 3.2 PA4547.472NLT PM4547.472NLT 4.70 1.90 220 264 2.8 PA4547.562NLT PM4547.562NLT 5.60 1.70 265 318 2.3 PA4547.682NLT PM4547.682NLT 6.80 1.50 290 348 2.0 PA4547.822NLT PM4547.822NLT 8.20 1.30 390 468 1.8 PA4547.103NLT PM4547.103NLT 10.00 1.20 435 522 1.6 Notes: 1. Actual temperature of the component during system operation (ambient plus verified in the end application. temperature rise) must be within the standard operating range. 5. Please note that the inductance tolerance of all parts are +/-20% except those 2. The saturation current is the current at which the initial inductance drops approxi- indicated with a * which are +/-30%. mately 30% at the stated ambient temperature. This current is determined by placing 6. Parts shown in bold are standard catalog parts and are available through sample the compnent in the specified ambient environment and applying a short duration stock and distribution. Parts in lighter font are available but are not necessarily held pulse current (to eliminate self-heating effect) to the component. in sample stock or distribution and lead times may be longer. Please contact Pulse 3. The rated current is the DC current required to raise the component temperature by for availablity. approximately 40C. Take note that the components performanc varies depending 7. Both the PA and PM part numbers are AEC-Q200 qualified parts. The PM part numbers on the system condition. It is suggested that the component be tested at the system have full automotive IATF16949 certification. The PM part number dimensions are level, to verify the temperature rise of the component during system operation. 100% tested in production but do not necessarily meet a product capability index 4. The part temperature (ambient+temp rise) should not exceed 125C under worst (Cpk)> 1.33 and therefore may not strictly conform to PPAP. case operating conditions. Circuit design, PCB trace size and thickness, airflow and 8. Special characteristics other cooling provisions all affect the part temperature. Part temperature should be Power.PulseElectronics.com P824.G (07/20) 1 1 6 9 4 9Marking Marking SMT Power Inductor High Current Molded Power Inductor - PA4547 & PM4547 Series POWER PRODUCTS Mechanical PA4547/PM4547 A C D L XXX G SUGGESTED PAD LAYOUT FINAL LAYOUT Series A B C D E L G H PA4547/PM4547 3.50.3 3.20.2 1.30.2 0.70.2 1.20.2 4.1 1.9 1.45 All Dimensions in mm. TAPE & REEL INFO W A K P 0 1 G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) TAPE SIZE (mm) QTY A G P W K PCS/REEL 1 0 PA4547/PM4547 330 12.4 8 12 1.8 3000 Power.PulseElectronics.com P824.G (07/20) 2 B E H