Dupline Universal Analog Input Module for DIN-Signals Type G 3429 6470 4 isolated analog inputs Inputs individually configurable for 0-20 mA, 4-20 mA or 0-10 VDC Selectable resolution: 1/1999 or 1/255 of full scale Selectable data format: 8-bit binary, Analink or 3 1/2 digit BCD EMC immunity according to EN 50082-2 (industrial environment) DIN-rail mounting (EN 50022) Address-selection through rotary-switches LED-indication for Supply and Dupline carrier LED-indication for invalid switch setting and 4-20 mA underflow AC or DC power supply Product De scrip tion Ordering Key G 3429 6470 024 Dupline 4 input univer- making a mix of analog input Type: Dupline sal analog input module for types on the same input H4-housing external supply. Analog values module possible. The trans- Transmitter on the inputs are converted mission format on Dupline No. of channels to digital values and trans- can be selected to fit the Input type mitted on Dupline . Inputs input module into existing Power supply are isolated individually to installations, or simply to use prevent ground-loops and to the most suitable combina- simplify installation. The input tion of resolution and speed. type can be selected as 0-20 The formats are: 8-bit binary, mA, 4-20 mA or 0-10 VDC Analink and 3 1/2 digit BCD for each input individually (with or without multiplexing). Type Selection Supply Ordering no. 24 VAC G 3429 6470 024 115 VAC G 3429 6470 115 230 VAC G 3429 6470 230 10-30 VDC G 3429 6470 800 Input Spec i fi cations Inputs set to voltage measurement Inputs set to current measurement Signal Signal input DIN-voltage input DIN-current input Signal range 0-10 VDC 0-20 mA / 4-20 mA Max. input level 50 V 50 mA Input resistance 125 K 100 shunt resistor Resolution A/D 11 bits or 8 bits 11 bits or 8 bits Transmission 1/1999 or 1/255 1/1999 or 1/255 Settling time ts 3 s 3 s Inaccuracy (ref. temp. 25C) < 0.5% of full-scale < 0.5% of full-scale Temperature influence (ref. temp. 25C) < 10 ppm/K of full-scale < 10 ppm/K of full-scale < 50 ppm/K of reading < 50 ppm/K of reading Common mode rejection > 120 dB (50-60 Hz) > 120 dB (50-60 Hz) CMRR Input-Input > 80 dB (50-60 Hz) > 80 dB (50-60 Hz) Normal mode rejection > 45 dB (50-60 Hz) > 45 dB (50-60 Hz) Cable length < 25 m < 25 m Dielectric voltage Input - Input 250 VAC (rms) 250 VAC (rms) Input - Dupline 250 VAC (rms) 250 VAC (rms) Specifications are subject to change without notice (23.10.2014) 1 G 3429 6470 Supply Spec ifi ca tions General Speci fi ca tions Power supply AC-types Overvoltage cat. lll (IEC 60664) Power ON delay 4 s Rated operational voltage Indication for through term. 21 & 22 230 230 VAC, 15 % (IEC 60038) Supply ON LED, green 115 115 VAC, 15 % (IEC 60038) Dupline carrier ON LED, yellow 024 24 VAC, 15 % Underflow (4-20 mA) LED, red Frequency 45 to 65 Hz Illegal switch setting LED, red - flashing Power consumption typ. 5 VA Environment Power dissipation 6 W Degree of protection IP 20 Transient protection 230 4 kV Pollution degree 3 (IEC 60664) 115 2.5 kV 024 800 V Operating temperature 0 to +50C (+32 to +122F) Dielectric Voltage Storage temperature -20 to +85C (-4 to +185F) Supply - Dupline 4 kVAC (rms) Humidity (non-condensing) 20 to 80% Supply - Signal input 4 kVAC (rms) Mechanical resistance Power supply DC-types Overvoltage cat. lll (IEC 60664) Shock 15 G (11 ms) Rated operational voltage Vibration 2 G (6 to 55 Hz) through term. 21 & 22 800 10.5 V - 30 VDC (Ripple incl.) Terminals Screwterminals Ripple < 3 V Tightening torque 0.8 Nm Reverse polarity protection Yes Power consumption <1.7 W Dimensions H4-Housing Power dissipation < 5 W Weight 300 g Rated impulse withstand CE-marking Yes voltage 800 V Dielectric Voltage Supply - Dupline 500 VAC (rms) Supply - Signal input 250 VAC (rms) Switch Settings Shunt-switches on system top Rotary switches in the front A-P 0-F Mode ON 3 1/2 digit: Channel group-pair Mux. address for input 1, Ex. setting: rest of the inputs (if enabled) C or D = C-D on the following addresses 8-bit: Channel group Mux. address for input 1, 1 2 34 rest of the inputs (if enabled) Current shunts on input 1-4: on the following addresses ON = 0-20 mA / 4-20 mA Analink: Channel group Channel no. for input 1, rest of OFF = 0-10 V the inputs (if enabled) on the following channels. Setting of 0+9-F is not valid. Function switches in the front ON 1 2 6 7 34 5 8 9 10 Offset on input 1-4 ON = 4-20 mA OFF = 0-20 mA / 0-10 V No. of enabled inputs OFF ON : 1 ON OFF : 2 ON ON : 3 OFF OFF : 4 Mode (Format) OFF OFF : Analink OFF ON : 8-bit binary ON OFF : 3 1/2 digit BCD ON ON : Reserved for future use Multiplex ON/OFF (Only used in 3 1/2 digit BCD and 8-bit binary mode) ON = Data is multiplexed OFF = Data from input 1 is transmitted on the group (or grouppair) rotarysw. A-P is set to, data from input 2, 3, 4 (if enabled) on the following groups (or grouppairs) Reserved for future use Dont care 2 Specifications are subject to change without notice (23.10.2014)